![]() If you don’t want to use a terminal wire connector, you can twist the wire ends and cover them with shrink tube or use an end cap. Matching the polarity of each wire (black with the – (minus) sign and red with the + sign) soldier the wires to the metal you’ve already soldiered over the copper terminals of the LEDs.Then use the soldering iron again to melt the solder onto the exposed wires. Twist the end of each wire to wrangle the frayed strands together.You can get wire strippers from any hardware store. Use wire strippers to strip half an inch (1.3 cm) off the wires’ ends.Cut the black and red wires to whatever length you need and pass them through the plastic end cap’s hole.Cut a small hole in it with a box cutter – small enough for a couple of wires. Get a plastic end cap from a hardware or home improvement store.You only want to melt enough of the wire to create small puddles of metal covering the copper dots on the LEDs. Melt the solder wire with the soldering iron directly over the copper dots. Then, hold a metal solder wire over the LED strip’s copper terminals. Get a soldering iron from a hardware store and heat it up.Remove the plastic cover or adhesive backing off the copper dots on the LED strips.We recommend using a quick connector in virtually every situation but soldering can work as well – it’s doing the same thing, only without a quick connector. ![]() If you don’t want to use a quick connector, you can try soldering the LEDs together. Plug the whole thing into a power source and that’s it. ![]() Then, just turn the connector’s screws clockwise to screw the wires into place. Match the black and red wires to the right slots on the terminal wire connector. If you don’t have one, you can get it from any hardware store. Connect the quick connector’s wires with a power source with a terminal wire connector.Close the plastic bar of the LEDs back over the quick connector.Plug the LED’s copper dots to the quick connector.If there’s no adhesive backing but a plastic cover, use a box cutter to gently cut the plastic off the terminals. Only pull it back enough to expose the copper dots/terminals for the connector. Peel away the LED’s adhesive backing 1⁄4 in (0.64 cm).Line up the black wire with the – (minus) sign and the red wire with the + sign. The connector should have two wires, one black and one red. Locate the + and – symbols on the back of the LED strip, on the other side of the copper dots.It’s delicate, so be careful and just pull it forward. It’s usually black and it’s at the end of the connector. Pull the plastic bar 1⁄8 in (0.32 cm) off of the quick connector.This is a very hassle-free way to connect the copper dots on the LED strips to the electrical circuit. Quick connectors are simple devices that are sold at any hardware store, plus they can be bought together with your Govee or other LED lights. The easiest, simplest, and quickest way to go about it is to just use a quick connector. This is the more complicated part of the process but it’s also very doable. Now that you’ve got a LED lights strip of the appropriate length, it’s time to connect it to a power source and place it where you want it to be. Again, test on a short strip first if you’re not sure how sharp your scissors are or you’re worried that you’ll mess something up. You don’t want to cut the copper dots themselves as then the entire LED strip won’t be able to be powered.Īnd that’s it – there’s nothing more to it. Use sharp scissors or a sharp box cutter and cut the line between the copper dots as precisely as possible.If you want to practice first, cut off a short strip to test on. Decide what length you want for your strip and measure it.The cut line will be surrounded by copper dots on each side. Each strip has specific cutting points between every two or three LEDs that are easily noticeable. The trick is in knowing where to cut Govee LED lights. LED light strips are meant to be cut into whatever length you want and Govee LED strips are made as easy to cut as possible. The whole process is relatively simple but it can be daunting at first. However, many are unclear about things such as can you cut Govee LED strip lights, how to connect them together, and other such questions. ![]() They are affordable, easy to use, and are becoming more and more popular for good reasons. They offer nice, unintrusive, and pleasant light that’s perfect for accenting certain objects and areas without being too bright and unpleasant. LED light strips are one of the best and most fascinating ways to decorate and light up a room or a space.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |